Leads & Adapters

A range of replacement curly leads, extension leads, and cross-over adapters.

Standard Replacement Lead (4 core)

L14
Add to cart

A standard replacement curly mic lead.

4 wires + shield

Extra Long Replacement Lead (6 core)

L16
SOLD OUT

An extra long replacement curly mic lead, approx half as long again as the one found on an average mic.

Length will be listed as either 3m or 10ft - either way this would be if the lead was stretched out straight, which is never going to happen.

Available with 5 wires + shield.

Thin Replacement Lead

L24
Add to cart

thinner than normal replacement curly mic lead.

Designed as a replacement lead for some of the smaller mics - such as the one on the Midland 77-095 etc.

Available in 4-wire only (3 + shield).

The picture shows it on the left next to a standard lead for comparison.

Speaker/Mic Replacement Lead

L27
Add to cart

A replacement lead for a speaker/mic complete with a fitted 2-pin plug (2.5mm + 3.5mm).

Different versions are available to order - some with stereo 3.5mm plugs and some mono.  State your requirements when ordering.

Add to cart

A shielded straight microphone cable, for making up extensions or adapters.

4 cores plus an overall lapped screen.

Outer cover is GREY.

This cable is thicker (approx 7mm) than the ones below which have more cores.

Price is per metre.

Add to cart

A shielded straight microphone cable, for making up extensions or adapters.

4 or 6 or 10 cores plus an overall lapped screen.

This cable is much thinner than the 4 core cable above, the 6 core is approx 4mm and the 9 core approx 5.5mm.

Price is per metre.

Microphone Extension Lead

Add to cart

A curly microphone extension lead, with a socket on one end and a plug on the other.

Available in 4, 5, 6, 7, and 8 pin.

(4,5, 6 & 8 pin are curly leads, the 7 pin is straight cable).

Microphone X-Over ( changeover )

Please call us to check whether we can make a particular lead & to order.  Online ordering is not available for this item.

We can make up cross-over leads for most radios - to allow you to use your mic on 2 different radios.

Just let us know what the mic is wired for and what radio you would like to plug it into, and we will make the adapter to suit.

Note:  these leads are for use on CB Radios only, we do not make them for Amateur radios

Add to cart

A solid one-piece microphone changeover adapter - with a socket on one end to plug your mic into and a plug on the other to plug into your radio.

Allows you to use a different mic on your radio without the need for rewiring it.

Available in 4, 5 & 6 pin versions for a variety of radios - see "more details" for the full list.

CRT SS7900 & CRT 2000 Mic Adapter

7900X
Add to cart

A microphone adapter to allow you to use a standard 4 pin microphone on the CRT SS7900 and CRT 2000 radios that have a modular type mic socket on them.

Available in 4 pin Uniden, 4 pin Cybernet or 6 pin Midland/President wiring.

CRT Milenium (RJ12) Mic Adapter

MILLX
Add to cart

A microphone adapter to allow you to use a standard 4 pin microphone on the CRT Milenium radio that has a modular type mic socket on them.

These are a smaller

Available in 4 pin Uniden, 4 pin Cybernet or 6 pin Midland/President wiring.

SOLD OUT

A very useful tester for checking microphones.

LED's show correct RX & TX operation, and a built in amplifier and speaker allow you to check the audio from the mic.

7 different sockets allow you to test most mic wirings.

Requires 12v power supply.